upgrades

hello again fellas.... the driveline in the xsc xb how does it hold up? ie diffs, bones, drive lines, cups also the clutch bell? thanks ahead of time fellas...any info is appreciated.

i ordered the gear plate with bearings,,,, for a gear plate upgrade,, the mt blue one,,, came with 10 bearings,,, im short one,,,,came with six larger ones,, and 4 slightly smaller ones,,,,used one larger behind plate for clutch bell,, 4 more on gear plate, and one short on the inner support for...

I know this has been covered but I have gone all the way back to 2008 in the forums looking at some of the recommendations and I'm wondering how many fixes the manufacturer has done in 4 years that I no longer have to worry about. I'll tell ya what I have so far and please let me know what...

Ok so the new motor arrived and so did the needed parts for the belt drive and the bell part # 50029n the outer bearing on the gear mount will not fit the shaft. Does anyone know what size this is? I was under the assumption they were all the same size but thats what I get for assuming i guess

Well since I had the problem with the screw that did not want to come out while replacing the clutch and had to wait for parts I decided to do some upgrades, I stripped the truck painted the chassis, replaced every bearing on the truck, made chassis supports, put in 8000rpm clutch and TR clutch...

Hey guys so just thinking ahead. What is a good motor to upgrade that would be a direct fit in the XT. I have a Flowsystem Pipe as well. I wouldn't want one that's overly powerful like the TR/OBR 8.2 hp engine where I would likely damage by drivetrain every other run. But what do you guys think...

I don't like the stock throttle horn for it's plastic. Any recommended aluminum horn that will work with my XB with very or no mod? Please let me know.

What would be the parts on MT,xt,xb,xbe,xsc and dunnrunner that you would want upgrade parts for that are not available?

So what are the recommended durabilty upgrades for this buggy to make it a worthy basher? Any suggestions are greatly appreciated. Thanks!

If only there is a titanium or steel part upgrade for this part... I would pay for it. Price does not matter. Just as long as its not over $100 :D And its guaranteed to last forever :D

Just got my xt and in my second tank I was turning and the front axel broke the c-hub any up grade on this

Want to replace both stock steering servos in my MT pro V3 as they already died after only 3 tanks of gas! Searching has pointed me to the Hitech 5755MG but I have questions. Do I have to order them to operate in different directions? Do I use the stock arm or upgrade to aluminum arms? What is...

I am selling my Rampage MT V3 I just have not been using the truck and am getting out of the RC Hobby to persue other interests. I am the original owner and the trucks has lots of upgrades. Upgrades: CPI Tuned Rear exit pipe 24 mm wheel adapters 4 Proline Bowties tires on Desperado rims...

I have two rtr trucks and would like to upgrade to a better transmitter/receiver. One is a 1/10 scale brushless and other is a Rampage MT. Not looking for the best. Just better.

Tons of options for the 5ive, what are the highest HP options for the Dunerunner? Mike

Well took my MT out to our 5th scale only track and was only redcat umong all losi and Baja. I was in 3rd with 2 minutes left and off finish line jump my left steering shattered!! I was pissed. Now need aluminum steering parts. But will be ready to take them on next time. Way happy with how the...

im sure this has been asked before, But here it goes: I will hopefully have a new Dunerunner soon. I will be mainly driving it at the sand dunes at the beach. No racing at all and I am sure , the stock speed is plenty for me. What kind of upgrades would you recommend ? I was reading...

My Spekrum DX3.0 to a better radio with multi model memory. What info can you give me? Thanks

Finally got my new gas tank done also added a cpi pipe and also milled out a billet hpi fuel cap

Finally got my new gas tank done also added a cpi pipe and also milled out a billet hpi fuel cap