gas

hi I have a HY 30cc engine and I need a new gasket part number 25045 it is call a air inlet pad and was wondering does the cy gaskets fit the HY engines as they don't have any listed gaskets for HY

what difference on the engines does the gasket thickness makes I see they come in 005, .012, .020 and more, and is there a difference in the copper heavy duty steel which is better? Thanks in advance.

What is the stock head gasket thickness cheers for help.

OK, so yet another problem, LMAO... (kinda getting sick of this crap) anyways, I just got in from replacing the base gasket on my MT with the 30cc fuelie engine. It started fine but idle'd very high before I took it all apart, hence the base gasket being blown out, so I replaced the blown out...

Can anyone answer me this question. I decided to use my RedCat Polished Aluminum tuned Pipe on my MT V4 coz' the wife said I can't buy a jetpro right now. So I did my break-in and when i pulled out the stock pipe, the gasket ripped into small pieces. I was hoping to use that gasket. then when I...

I just got an XT used with a 26cc engine but the base gasket is blown, I ordered the parts from DDM, I am more then capable of doing this repair, I just don't know where to start, I have the engine removed and ready to go, I just need some instructions... As always any and all help is very very...

Just to make sure on the gas mix is it 1g of gas and 5.2oz or 4oz of 2 cycle oil? what brand of oil?

Ok i ran my MT a few days ago and it seemed to run better than ever !! and i went to run it today and it has a blown cylinder gasket soon as i crank it. its idled up crazy WTF ???? It was running so good when i cut it off a few days ago Anyone else had a base gasket blow out like this

Half way done pic of my bud's new gas cap vent installed on his cherry XT. Just waiting for the one way fuel filter to arrive. We talked him into installing one. All credits for this mod goes to "forist" though. we got this idea from him when our XB and XT stopped all of a sudden. then we found...

This is how I have my gas cap vented thought i would post it up hope it helps some others with gas tank vent probs. i bought the filter on ebay is is one way filter so you don't have to worry about the gas coming back out on a roll over. Hope this helps.

what can i do to stop this..its leaking out the top of the pin hole and leaking down thur the lid where it screw down on the tank..can someone help me or tell me what i can do

I've had my Rampage MT shut off at wot several times then start and shut of after that. Ended up finding the gas cap vent plugged. Took the cap apart cleaned out all the holes runs great. This has happened 3 times since I bought the truck. Does someone make a better cap or anyone have ideas on a...

Is it normal to open the gas cap and hear a vacuum sound, like air going in?

Just to make sure on the gas mix is it 1g of gas and 6oz of 2 cycle oil? I was using 87 regular with 2cycle oil synthetic from home depot is this ok?

I just bought one of these Blur gas tank vent filter and would like to hook it up to my gas tank cap. I also bought a perry check valve because I see some are installing them to prevent gas from coming out during a roll over. My question is with the perry check valve, should I now remove that...

Can someone post a link for what replacement gasket I need for the exhaust side of the head please. Thanks in advance

Anyone know what the proper seal thickness is for the stock 30.5 hy motor?

iam getting new Copper Cylinder Gasket, for my cy27cc what size .020 or .040?

i went to change my front center dif drive cup cause its warn and i see it is rubbing on the gas tank. i had to grind the edge off the new one so it now just misses the tank. can someone check theirs for me.

Hey guys... was wondering if any of the aftermarket aluminum gas caps for the Baja 5B fit on the redcat rampage mt? Blur racing has a real nice one for the baja i'd like to get but not sure if they will fit. Thanks!