Search results

Where can I get this garage! I hate youuuuuu :p .

Parkling lot got full in the later vids, tell them jerks it's RC parking only! Great quality, can't wait to see some on board cam shots off road.

I bought the bag from mcMaster. I'm waiting to sell my XT so I have no use for them. I can send you some (like 4/6/8 whatever) for free. PM your address if you haven't ordered your own already.

Anytime you up the pinion you'll get more speed, granted the new amp draw can be met by the batteries and ESC. if 48spur going up from 10 to 11 changed FDR from 14.4 to 13.09. That's a big change.

Yes, any friends I get into 1/5 scale RC i don't let em run without a killswitch. These things are absolute death missile. I've seen what one does to a car in a parking lot out of control. I would hate to see the day it take off across the park into the children sand box.

What was your break in procedure? A lot of this fine tuning is after you break it in, and you are 'tuning' in the engine for its sweet spot. Before that you have break in, which I usually go about 5 tanks on for the overall procedure. I do all this while on the rich+ side. There's several...

That's pretty bad ass. Not gunna lie.

Use a high temp, semi thick squish gasket, or do as I do and use this. Available at any auto store. http://www.motorcycle-superstore.com/4/22/269/22864/ITEM/Permatex-Ultra-Copper-Silicone-Gasket-Sealant.aspx

I wish it had a true center diff, and the least a slipper. I would have got one then.

read up a bit more, I'd go 668 at as well. Good price.

He's got a modified baja rear dom pipe, and taller gears is all I think if memory serves me right.

That is something I actually haven't had to do on mine. So i'm not the best in that area. I'd personally go Walbro 990. http://www.davesmotors.com/s.nl/c.885035/n.1/it.A/id.7550/.f There are different types of gaskets, not sure on the 'best.' Hear about blue ones, and copper ones ect ect. There...

and you are using a new plug right? I would start lean on the low needle, listen how she sounds every two pulls. Keeping bumping it up an 1/8th of a turn out if she doesn't start after two pulls at each setting. IF you get all the way to the recommended starting point and no luck, i'd see your...

If you put your thumb over the spark plug hole, and pull do you feel compression?

Could be set screws as already said. It can also deal with how your linkage is setup. YOu may not be getting full breaking just based on the setscrew/collar that retains the spring on the breaking linkage. I run fuel tubing vs. a spring, and my breaks come on quick, and at full lock up. Mine is...

That could be a sign of a leaky gasket if it's really oily and caked on from only a few runs.

The primer bulb not emptying with all needles closed it correct. It should NOT let any fuel into the carb when the venturi create the vacuum. The reason for the test is sometimes these junky carbs will get the needle screw springs bound up, or a bit too long. What happens is 'fully closed'...

I don't think the problem is a lack of disclosing that they are soft, and knowing what you are buying, but more of 'they are shit'. It's an AT tire that sells itself as an AT tire, yet it's too soft to work as an AT tire. With that being said, if you want an AT tire, and they are disclosing they...

Pretty sure there aren't any. May have bit more luck posting this in the hop-up section as well vs. engine area.

Have you tested that you are still even getting a spark now that it's clean and your flywheel gap is good? Should be able see it sparking following the standard method to test the plug outside the engine. Carb could be shot, could be something worse inside the engine itself. IF you fill the...