Inertia Racing Products
Well-Known Member
- Messages
- 95
- Location
- S.E. Texas
Hi Guys,
i received my XB last night so i thought i would share the build as it comes along.
So lets kick this bad boy off !!
1st steps
Motor
______
I am yanking the motor and pipe, not even going to fire it off, and i will be selling it as a drop in unit.
The new mill will be my Gizmomotors 30.5 ground pounder with Walbro 990 carb, Shreadstack inclined stack, and probably the HPI air filter set up with outerwears.
The pipe of choice for this beast will be the DDM Sidemount, with a few mods for proper fitment.
The clutch of choice will be the liteweight shoes with the 8000 rpm spring
Polished Billet Fan Cover with DDM pullstart and outerwears.
I will also be swapping out the plastic mount with the 7075rc billet plate
Driveline Mods
_______________
7075rc c-hubs
7075rc Front bearing holders with new bearings
7075rc Rear bearing holders with new bearings
these will be here today !!
Suspension Mods
_______________
i will be making my own Custom Front and Rear Billet 6061 T6 Shock Towers
Multi position mounts.
Shocks are out the door, going to mod a set of HPI 5b fronts for all 4 corners with Phatdads 6mm shafts, Threshold Ubmbrellas, and my own internal limiters, going with Blue HD springs.
Rear Camber Links will be a set my own V2 Billet center links with 4130 Chrome Moly rod ends
Front upper Control Arm Links will be a new custom made set out of my shop with 4130 Chrome Moly rod ends.
Electronics
___________
Servos are history
going with Rhino Digi 4 Multiplex steering with billet horn i have sitting in the parts bin, probably end up making my own mount.
T/B will be a new hitec 5645mg
Reciever will be a Futaba R603FS to match up to my 4PK
Receiver pack new DDM Black Magic
Killer Bee Kill Switch.
Well thats about it for now.
i do have plans to make up a set BRP hub adapters for this rig to run his tires and wheels, thats down the road a bit , but not too damn far !!
I'll post pics as i go .
i received my XB last night so i thought i would share the build as it comes along.
So lets kick this bad boy off !!
1st steps
Motor
______
I am yanking the motor and pipe, not even going to fire it off, and i will be selling it as a drop in unit.
The new mill will be my Gizmomotors 30.5 ground pounder with Walbro 990 carb, Shreadstack inclined stack, and probably the HPI air filter set up with outerwears.
The pipe of choice for this beast will be the DDM Sidemount, with a few mods for proper fitment.
The clutch of choice will be the liteweight shoes with the 8000 rpm spring
Polished Billet Fan Cover with DDM pullstart and outerwears.
I will also be swapping out the plastic mount with the 7075rc billet plate
Driveline Mods
_______________
7075rc c-hubs
7075rc Front bearing holders with new bearings
7075rc Rear bearing holders with new bearings
these will be here today !!
Suspension Mods
_______________
i will be making my own Custom Front and Rear Billet 6061 T6 Shock Towers
Multi position mounts.
Shocks are out the door, going to mod a set of HPI 5b fronts for all 4 corners with Phatdads 6mm shafts, Threshold Ubmbrellas, and my own internal limiters, going with Blue HD springs.
Rear Camber Links will be a set my own V2 Billet center links with 4130 Chrome Moly rod ends
Front upper Control Arm Links will be a new custom made set out of my shop with 4130 Chrome Moly rod ends.
Electronics
___________
Servos are history
going with Rhino Digi 4 Multiplex steering with billet horn i have sitting in the parts bin, probably end up making my own mount.
T/B will be a new hitec 5645mg
Reciever will be a Futaba R603FS to match up to my 4PK
Receiver pack new DDM Black Magic
Killer Bee Kill Switch.
Well thats about it for now.
i do have plans to make up a set BRP hub adapters for this rig to run his tires and wheels, thats down the road a bit , but not too damn far !!
I'll post pics as i go .