rampage xt

I Put a side mount Jetpro pipe on my XT last night and see that its resting on the rear shock tower brace. Will this cause issues with melting? JD

Hey guys new to the forum, had my xt for a few months now but im having trouble adjusting the low speed needle. I watched a lot of the videos that I could find on youtube about how to adjust the needle and what the factory needle setting are but here is my issue. when I have the lsn set at...

I'm over the break in period and we're on about the 3rd tank of fuel now. After running it pretty hard up and down a grass covered field then slowing down to a complete stop. Then engine died on us. This happened 3-4 times overall in about a 30 min time period. Note that within a pull or two it...

I have an XT and walbro 990 carb with CPI pipe. engine ran fine for a couple of tanks after pipe was put on, then started to really bog until about 3/4 of full RPM then takes off like a banshee. I have tuned it every way possible and nothing will change it. Another guy I know is sending his...

I've been thinking about widening my MT a bit and was wondering what you guys have tried and what you'd recommend and of course the pros and cons at first I was thinking about trying 1/2" axle extending but I got thinking about wheel bearing wear/failure then extended a-arms came to mind are...

Is there a product out there that can make this happen. I want to extend my intake to bring it up to the front so it can actually look like a real intake from under the hoob. Something like a manifold extender of somewat??

I have a rampage XT I need a new pipe for and a seat of tires too pls

Not sure if anyone is interested or not but I modified the Rampage XB to accept the HPI Baja 5b rear hub assemblies. It was a very easy mod. and only required about 10 minutes per side to complete. 1. Remove Rampage hubs and bearing holders 2. Drill the rear outer "A" arm hinge pin hole to...

just received my new xb/xt shocks and was wondering how to bleed them,are they bled the same way as the HPI baja shocks? I also noticed on these shocks that your unable to remove the whole shock shaft without removing the top nut and piston,is that the proper way to remove the shock shaft if...

Hey folks... Well i was blasting around some fields with my Redcat Rampage XT when something in the drivetrain let go. My clutch engages and the drive train gears turn, but there is no power to the drive line. When i turn the wheels everything turns including the driveline gears going towards...

Wondering the difference between a Rampage MT and a Rampage XT? Redcat has created a video that shows how they compare in size: http://www.rampageshop.com/3/post/2014/04/rampage-mt-vs-rampage-xt-size-comparo.html I put a few screen captures and notations in the post as well so you can skip...

I need to try a set of Hostile MX, thing is I do not know what rims and foams to insert. I have no clue regarding them. any DDM link would be appreciated -Tire: Extra Hard Compound Hostile MX Rear -Tire: Hard compound MX front -Rims? (front/back) (please link) -Foam? (front/back)...

Okay, so i had a simple question, would it be possible to swap a 3s lipo end on connector and hook it up directly to the truck? or what battery do you guys suggest for the longest run times. I really don't wanna have to go through a ton of batteries. Any input would be great, thanks all!

Just a thought.... another HiTec servo would only be $50. Switching to a lipo system (if I remember right will be around $150). I have a 5900mah 6v battery and love the longevity so would kinda like to keep it. I tried a 'search' with no relevant results. Is there a dual servo conversion...

I lost the lower sleeve and screw on the right front hub. It was 60* out and haven't ran the truck in a couple months so I continued to run it lol. Go figure I clipped a branch on the ground and the hub broke. Could I just pick up a right side front hub with screws/screw sleeves?

I thought my HQ steering servo went bad because instead of returning to zero, it would turn left even after I re-centered it and adjusted the knob on the controller. I installed a new HiTec servo and it's doing the same thing. What would cause this? :confused:

Hey guys. Here's another noob question. I'm not too good with small engine carb adjustments. Ive figured out where the idle screw is, but there are 2 other screws on the 30cc Fuelie right next to each other. I'm assuming that these are mixture screws? I don't have the Rampage manuals, didn't get...

I was looking at the parts manual for the XT the center diff cup facing the front is part #07146 I found that but the rear facing cup is part #07164 cant find anywhere is this a misprint are they the same part?? THANKS

i've heard people say it raps around 10,000 and heard people say it raps 7,000 idk what it raps

Has anyone ever used this? I have two quarts sitting here that I bought. What is everyones thoughts? It says to mix at 50:1 which I will just ignore....