Gears???

[kydo32]

I have mt and stripped the gears I am putting new ones on I have square drive gears but don't know which go where I know the 35 tooth but I have three 25 tooth one is flush where square is on back of gear and the other 2 have the square sticking out of gear.my question is where does the flush one go on brake,behind 35 tooth ,or on clutch bell shaft ?????

 

[kydo32]

anybody?????????????????????

 

[BertR]

The square's have a dome on one side that should be facing the plate. Do you have a square on backwards?? It shouldn't matter where the 25's go

 

[kydo32]

The square's have a dome on one side that should be facing the plate. Do you have a square on backwards?? It shouldn't matter where the 25's go

see how top gear is flush where square is and thicker width the bottom two have ridged squares sticking up and thinner width. which go where ? didn't notice there was a difference when I removed them. View attachment 7530 they all are the 25 tooth



/monthly_2014_10/583c6071654fa_gears001.jpg.5fb1a87cd3184dfd714f8551e6777442.jpg

 

[BertR]

OK I see what your saying.. The flush one is most likely your D gear and the other 2 are C & A.. The D gear takes the most abuse.

 

[kydo32]

OK I see what your saying.. The flush one is most likely your D gear and the other 2 are C & A.. The D gear takes the most abuse.

d gear? which is that? I have gear for the clutch bell shaft, one for the brake shaft and the free spinning one which has 25 and 35 tooth . so which is what?

 

[BertR]

The thick Flush one will go on the break shaft and the other 2 just pick a spot for them..the lutch bell gear is “ A” there is a sticky with the diagram in one of the sections for the mt at the top of a page.

 

[BertR]

The sticky is above your thread title called Gearing options.

 

[Phill]

 

[BertR]

Thanks Phill. I tried to get my phone to copy & paste but had no luck so I had to go the long way lol.

 

[kydo32]

Great thank you for the help!!!!

 

[kydo32]

Thanks Phill. I tried to get my phone to copy & paste but had no luck so I had to go the long way lol.

how come when I got my gears on they don't line right up center to center View attachment 7539 View attachment 7540 View attachment 7541 on my gear from motor it sets on the inside part of the 35 tooth not in the center and the gear goes from behind 35 tooth to brake is set to the back side of gear











/monthly_2014_10/583c607183bda_g001.jpg.41032227db6e7ca8fceadb2909e15bb0.jpg

/monthly_2014_10/583c6071852b1_g002.jpg.b23d05977b3ebb9ba721360676bc491c.jpg

/monthly_2014_10/583c607186a1d_g003.jpg.39b56385f4fdaa6545a11b09a1efcd3d.jpg

 

[Phill]

At a guess I would say your B & C gears are wrong way round maybe ??

 

[kydo32]

At a guess I would say your B & C gears are wrong way round maybe ??

they can only go one way that is the b gear 35 tooth and the c gear is 25 tooth they look nothing like the gears on post you posted they don't line up in center of gear also that pic shows wider gears then what came off my mt

 

[Phill]

they can only go one way that is the b gear 35 tooth and the c gear is 25 tooth they look nothing like the gears on post you posted they don't line up in center of gear also that pic shows wider gears then what came off my mt

There is definately something wrong on that B/C shaft.

Did you leave a shim out?

 

[kydo32]

There is definately something wrong on that B/C shaft.Did you leave a shim out?

no was a washer between gear and bearings I put back in and washers behind nuts but other wise nothing else is missing

 

[Phill]

I'm sorry but I'm out of ideas

Maybe someone else can help

 

[kydo32]

I don't know if anyone else will help . when I first got my mt I asked a lot question now people ignore me and wont answer. its funny cause if you look back when some senior members were new they asked a lot questions too and nobody ignores them. I thought this site was for questions when I didn't know the answers but starting to feel like this site doesn't stand up for what it is here for Questions and Answers !!!

 

[RampageHopUps]

Unfortunately, sometimes it's hard to answer if you don't know the answer. Not everything is cut and dry and easily answered.

 

[kydo32]

you can see how A and B gears don't line up center and C and D gears don't either View attachment 7542 View attachment 7543 View attachment 7544 View attachment 7545

















/monthly_2014_10/583c607188359_gear004.jpg.603fab8718a4500373034f39d397c69e.jpg

/monthly_2014_10/583c607189bc9_gear002.jpg.81d650f3a0bbcf9ecb5175bc4889d281.jpg

/monthly_2014_10/583c60718b03d_gear003.JPG.41085dd56892731585c183d6f837e496.JPG

/monthly_2014_10/583c60718c366_gear005.jpg.6bc8435d7d405a10062d2d494baaf981.jpg