Search results

check youtube for tuning 2 stroke r/c engine. good stuff there. kinda need to know that makes all else easier.

the bind plug is only needed if your transmitter and receiver lose the signal between each other. I'm not sure but I think there is something in the manual about rebinding. the kill switch you can get from rob at redcat hopups on the left of this page or here...

I quite some time ago cut the right size drill bits off to length and put a flat spot in center and they're still working till this day. quick fix and durable.

you might try a catbox. better than stock and not that expensive.

the only redcat wheels that will fit m/t are the dunerunners.

I bought some kind of wd at lowes a while back that wasn't regular wd. whatever it was it smelled and worked just like rem oil,triflow,or triflon. I've actually found all 3 of those lubricants at lowes before but it's hit and miss from day to day as to what they may have and that depends on if...

you ever check out bonzi boats? I'm in love with the 84's but dang 15 hundred just for the hulls. heck by the time you get done rigging it with a 4 engine setup your out 10 grand. for that kind of scratch I'd want to be fishing out of it. http://www.bonzisports.com/

I normally don't chime in like I know what I'm talking about because there's just to many ways to skin any cat but in this case I've got to add my 2 cents. after you clean your truck using whatever cleaning fluid of your choice and using the sun or my way compressed air to dry it , lightly cote...

isn't this the same truck for less? http://www.kingmotorrc.com/4-wheel-drive/1/5-scale-x2-4wd-short-course-29cc-rtr-blue/

dave ought to be kicking back a little something to you for all that good publicity!! looking good!!

you might try this. https://www.aeroflowperformance.com/silicone/hose/hose-straight/straight-3-76mm/af9001-100

you know you could take the motor out and ship just it. there's no way that would be 250 to ship but if it was me and I had to spend any where near that kind of cash I'd put it toward a new motor and use the old one to practice up on my small engine repair skills. in fact ddm's deal of the week...

I gotten a lot of good tips from bert but in this case I've got to disagree. I've got two m/t's and a d/r and in my experience with them I haven't had a whole lot of luck with redcat servos. my first m/t with the end points set right the t/b servo shit the bucket after about 2 tanks and soon...

I really like these http://www.davesmotors.com/complete-ddm-hex-driver-set-standard-and-ball-end-with-handles-and-socket-holder.html with this set and a small powered driver life becomes much easier.

nobody ever figure out what happened to rcdad????

the one link that doesn't work was supposed to be for the killer bee kill switch but can't get the link to copy right so if you want to check that one out you'll have to go to killer r/c site. you can google it.

for some reason the one link didn't copy right. this should be it. http://www.com/product/super-bee-kill-switch-car-kit/

http://www.ebay.com/itm/RAMTech-RC-Kill-Switch-for-2-Cycle-Gas-Radio-Control-Vehicles-/291477569575?pt=LH_DefaultDomain_0&hash=item43dd6ac027 http://www.********.com/product/super-bee-kill-switch-car-kit/ here are two

+1 on the ddm dominator I haven't been able to break mine and it acts as a handle for carrying the truck when it's not hot.

http://www.davesmotors.com/hitec-hs-5645mg-35645s-digital-throttle-servo-metal-gears.html http://www.davesmotors.com/hitec-hs-805mg-32805s-steering-servo.html these will botn work